Tracii XL 2.0 - I2C High Speed Interface for USB

• High-end I2C Interface.
• USB 2.0 High-Speed (low latency in I2C master-mode, higher bandwidth)
• I2C master-mode including multi-master.
• All I2C transfer and address modes are supported, of course.
• All features are software controlled, no jumpers need to be set.
• Supports the I2C modes standard, fast-mode and the new fast-mode Plus.Controllable I2C transfer speed of 20 bit/s to 1000 kbit/s.
• The additional high-speed mode with up to 3.33 Mbit/s is a separate option.
• SMBus master (quick command, send/receive/write/read byte, write/read word, command process call,block write/read/write-read with PEC)
• 7 and 10 bit addressing
• Variable termination: 900 Ohm ... 10900 Ohm (64 steps) / no termination.
• Optional 270 Ohm termination for boosting SCL according to the HS specification.
• I2C bus voltages from 1.0 V to 5.5 V.
• Optional I2C Vcc supply: 1.0 V to 5.5 V (0.1 V steps)
• Adjustable I2C levels from 10% to 90%.
• Future-proof product: Firmware is completely downloaded via USB.
• I2C Slave: I2C RAM Emulation (256 bytes, slave address configurable).
• All options are software-enabled. So you may upgrade the product by getting a special key permanently enabling the feature.
• All features as I2C master, digital- and analog-tracer are running simultaneously on a single Tracii XL 2.0 supposed these options are enabled, of course. I2C slave and master cannot be used simultaneously.
• Plug and Play interface.
• No ROM onboard, i.e. firmware can be updated for future requirements.
• Multiple Tracii XL 2.0, Tracii XL, Connii and Connii MM 2.0 units can be connected to one PC.
• IRD (I2C Register Description) support
• I2C Flasher included for free
• TCP/IP Network support (I2C via Internet)
• ESD protected, IEC compatibility according to
  EN61000-4-2 (ESD) Air - 15kV, contact - 8kV
  EN61000-4-4 (EFT) 40A - 5/50ns
  EN61000-4-5 (Surge) 12A, 8/20µs - level 1 (line-gnd) & level 2 (line-line)
• No external power supply necessary.
• Solid stainless steel case of 105 mm by 130 mm by 42 mm.

The following features are options sold separately:

• Additional feature: monitoring of I2C bus and SMBus
• The bus monitoring is non-intrusive,of course.
• Tracii XL 2.0 can be used as a master AND a monitor at the same time with a single unit.
• Time measurement - time stamps - for every byte or event (start / stop condition).
• The I2C Tracer has a 200 ns resolution (independent of the HS option being enabled).
• Different to other solutions Tracii XL is able to monitor long, continuous I2C streams without slowing the I2C communication by stretching the bus.
• Tracii XL 2.0 continuously sends the trace data to the PC which is processed and stored by I2C Studio in real time. This allows virtually unlimited lossless data capture.
• Read, write and interpret E-EDID, i.e. DDC data
• This option is sold separately, you need to order Tracii XL 2.0 Option: Tracer Mode.
• Other I2C tracers are Connii MM 2.0 and Tracii 400

Price: Order your Tracer Option for 1450 € 

• Dual A/D converter with sampling rates of 78.43 kHz to 40 MHz.
• Tracii XL 2.0 can be used as a master AND, tracer AND analog monitor at the same time with a single unit.
• 256 kSamples are stored per SDA / SCL with 8 bit and max 5,5 Volts.
• Pre-trigger with 0 to 12.5%, i.e. 32767 samples equal to 3.3 ms at 10 MHz.
• Smart Battery System (SBS) high-level tracer
• For analog tracing you need Tracii XL 2.0 Option: Tracer Mode plus Tracii XL 2.0 Option: Analog Mode.

Price: Order your Analog Option for 1250 € 

• Adds the new I2C high-speed HS mode with up to 3.33 Mbit/s.
• Controllable I2C transfer speed of 305 bit/s to 3.33 MBit/s with optional behaviour according to the HS mode specification.
• This option is sold separately, you need Tracii XL 2.0 Option: High Speed.

Price: Order your High Speed Option for 600 € 

• This option enables Tracii XL 2.0 to support Labview, please order I2C.Labview
  more details >>>

Price: Order your Labview Option for 285 € 

• Windows 2000
• Windows XP (32-bit, 64-bit)
• Windows Vista (32-bit, 64-bit)

Tracii XL 2.0 is available with different configurations. The above table lists the superset. Features are enabled individually. The product price depends on the requested features. You may add new features to your Tracii XL 2.0 later on without returning it to telos.

Tracii XL 2.0 comes with an impressive bunch of free software:

• Application I2C Studio
• Library I2C Framework

• The Tracii XL 2.0
• Software package I2C Framework including all listed components
• Application I2C Studio
• No cables, please order them individually if you need them

• Full Mini-DIN (PS/2) cable
  To interface your I2C bus to a hardware with Mini-DIN interface.
• Mini DIN Test Probe
  To interface your lab equipment to our hardware.
• USB cable
  To interface to the USB port of your PC.
• Tracii XL 2.0
  I2C High Speed Interface for USB

You may of course use standard cables already available at your lab. The PS/2 cable quality might have impacts on the signal quality on the I2C bus.

This product comes with a bunch of software licensed for the lifetime of the product. Additionally you get a free service contract. This includes 12 months free support plus all software updates coming within this period. You may use all this software without time limitations.

• Order your Tracii XL 2.0 for 1100 €